How to install a dish network 500 antenna

Reactions: papachops , crodrules and MikeD-C Thank you for the info. I dug around and found an SW switch in a box of cables, splitters, etc that I have accumulated over the years so I should be good to go. Thanks for your help. I took your advice and ordered the dish I received the dish It has four ports on it. The three satellite ports and LNB in. I am wanting to connect it to one vipk receiver.

This is a simple setup for my RV. What do I need switch, splitter, connector, etc to connect the dish HIFI said:. Cable from the k to port 1 on the Previous Next.

Post reply. Insert quotes…. Similar threads J. JB Dec 23, Replies 10 Views 2K. Dec 26, Brisak. Installation Problem Dish Replies 5 Views 15K. Mar 27, JohnTenn. Replies 4 Views 1K. Sep 29, SimpleSimon. Dish Installation Question. Dec 19, viqventeur. JB Feb 20, 2. Replies 26 Views 4K. May 6, Jimmerinwi. Latest posts. Hopper 3 in Enclosed Cabinet? Latest: reubenray 19 minutes ago. Use the azimuth number to rotate the satellite. Have a compass handy and locate true north first.

Then, look at the azimuth number and find where that is on the compass. North is considered 0 degrees, east is 90 degrees, south is degrees, and west is degrees. Rotate the satellite dish horizontally until it points in the correct direction. Then, turn the satellite southwest from there.

Move the dish vertically to adjust its elevation. Once you know the height needed to reach the satellite, go behind the dish. Examine the end of the mount where it connects to the dish. You will see a bolt inside a slot labeled by degrees, usually 10 to Loosen the bolt by twisting it counterclockwise, then reposition the dish to the proper elevation.

Moving the bolt along the slot raises or lowers the dish. For instance, if the dish requires a degree elevation, it will point up into the sky almost as much as it possibly can. Slide the loosened bolt back toward the degree marker. Adjust the dish's polarization until you get a clear signal. The final part that needs to be adjusted is LNB, responsible for receiving and sending the signal into your home.

It is usually an arm on the front that points toward the dish. Test out the signal quality by hooking the dish up to the receiver and a TV, then loosen the connecting nut on the arm by turning it counterclockwise with a wrench.

If the TV is far away, have someone else stand near it and give you feedback. You may need to wait to adjust the LNB until you're done with the wiring. Take care of it before then, if you're able, so you don't have to keep climbing on the roof to make adjustments. The LNB can sometimes be controlled by turning a mount part on the back of the dish left or right.

Part 4. Check your home first for a previously-used cable opening. The dish's cable needs its own little space to enter your home and hook up to your TV.

Unless your home is in the process of being built, drilling a single hole is the easiest way to do this. Position your TV and the satellite receiver nearby to prepare for the connection. It needs to be below the frost line, the lowest point that freezes in winter, which is about 3 in 7.

Run a coaxial cable from the LNB to the receiver. Make sure the receiver is positioned close to the satellite to ensure the cable can reach it. TV service providers will also give you one when you buy a satellite from them.

The coaxial cable sometimes connects to the back of the satellite. Usually, though, it plugs directly into the LNB. Once the cord is in place, your TV will be able to receive the satellite signal. Turn on the TV to see if it works. The receiver may plug directly into the TV instead.

Consult a wiring guide for specific instructions on how to connect the satellite, receiver, and your TV. If you bought the satellite from a TV service provider, they would also provide a wiring guide. Turn on the TV to test the signal. Press the satellite button if your remote has one or navigate to the settings menu. You should be able to get a picture right away. If the signal quality is poor, make sure you positioned the satellite dish correctly.

Adjust it to get the clearest possible signal! Please note the azimuth, elevation, and LNB numbers and compare them to the satellite's location. Include your email address to get a message when this question is answered. Ask TV service providers for an install. Many of them offer free installations as long as you buy a subscription for their service. Helpful 2 Not Helpful 0. Find spots to hide loose cables in your home. If the satellite dish's cable is exposed, put furniture and other decorations in front of it.

Helpful 1 Not Helpful 0. Every satellite receiver needs a separate coaxial cable. You can't split the cable, so you will need to find ways to route the cables all the way to the extra TVs you plan on setting up.

If you're running a coaxial cable outdoors along the ground, consider installing a grounding block and wire to protect the cable from static. Helpful 1 Not Helpful 1. Submit a Tip All tip submissions are carefully reviewed before being published. Be very careful when climbing onto the roof to install a dish. Avoid dangerous falls by wearing a harness and working on a warm, clear day. You Might Also Like How to. How to. More References About This Article. Co-authored by:.

Co-authors: 6. Updated: March 30, Categories: Satellite Television. Bahasa Indonesia: Memasang Satelit Parabola. Thanks to all authors for creating a page that has been read 67, times. Is this article up to date? Yes No. Cookies make wikiHow better. By continuing to use our site, you agree to our cookie policy. Featured Articles How to. Trending Articles How to. New Pages How to. Find a location for the dish antenna with a clear line of sight and a sturdy mounting surface 3.

Mount the mast, making sure it is absolutely vertical 4. Assemble the dish antenna, setting the skew and elevation angles in the process. Use additional skew bolts for skew angles greater than or less than 70 5. Mount the dish antenna on the mast and point the dish to the azimuth angle 6. Run cables between the dish antenna and the receiver s , leaving a service loop around the Mast Clamp 7. Using a peaking meter attached to the DPP Tighten all bolts see Table 1 and re-confirm maximum signal Note: The Connect the receiver cable s to the DPP Some restrictions apply when connecting Legacy receivers.

Install additional receiver s , if necessary If applicable, connect a second satellite dish to the DPP Assembling and Mounting the Dish Follow these instructions to assemble the satellite dish, mount it, and point it in the direction of the satellites. Note: If your skew angle is at the extreme ends of the scale greater than or less than 70 , insert nuts and bolts from the hardware pack into the additional skew holes. These additional skew holes provide greater stability to the dish at these extreme angles.

See Figure 2. Installing the Receivers Use the steps below while referring to Figure 1. From the Point Dish screen, run Check Switch. On all other Legacy models, select Test. When the Check Switch procedure finishes, you should see an Installation Summary screen similar to the ones shown below.

Do not disturb the receiver during the process of downloading software. If exiting the Point Dish screen does not start the download process, turn off the receiver for at least 20 minutes on most receivers to allow the receiver to take a software download. Run Check Switch again and confirm reception for all three satellites on all available satellite tuners.