Kyocera fs 1800 manual

EcoPrint mode is factory-set to off and turned on by using the menu system of the printer operator panel. Page Replacing The Waste Toner Bottle Locate the new waste toner bottle in the toner kit, and install it in the printer according to section 2- Installing the waste toner bottle on page Page Cleaning The Printer Cleaning of the main charger can be done without needing any tools thanks to its self-cleaning system.

Pull the cleaning knob green colored 2 slowly in and out a few times. NOTE Cleaning knob pulls a cleaning pad inside the drum unit along the main charger wire. Page Grid Figure Grid cleaner 2. Attach the grid cleaner 1 to the drum unit 3 with the pad uppermost as shown in the diagram.

Page 64 The grid part underneath the main charger is cleaned by the wet pad of the grid cleaner. Figure Cleaning the grid 4. Remove the grid cleaner from the printer and dispose of it. The grid cleaner is not reusable. Page Paper Feed Unit 7, do not use alcohol to clean this area. If the oil is completely removed, an incorrect action of the MP tray paper sensor 8, actuator will result.

Page Replacing The Developer To pack the developer 1 in the packing carton, first flap down the magnet roller protective cover 2. Put the developer 1 into the supplied plastic bag 3. Put the developer 1 on the developer install position 4 of packing carton. Page Developer Initialization Toner Install Mode When printer power is turned on again, the printer continually engages in this mode for a period of approximately 15 minutes, after which the printer reverts to the ready state.

Default is 3. Page Drum Cleaning Mode Drum is cleaned by the cleaning blade in the drum unit. If paper is present on the MP tray, the drum is also cleaned by that the paper which is fed automatically and stops at the transfer roller. Ready 7 Turn power on again. Check the printer gets Ready. The data to be downloaded is perosonD3 corrupted. If the corrective action above does not solve the problem, replace engine board KP See page Page 77 3 Drum unit and developer Page Electrophotographic System The electrophotographic system of the printer performs a cyclic action made of six steps as follows.

Each step is technically explained in the following sections. Page Charging The Drum Therefore, it must be cleaned periodically from time to time using the method explained in chapter 3, page Cleaning the main charger wire B prevents print quality problems such as black streaks. These lenses adjust the diameter of the laser beam nm wavelength so that the laser beam effectively focalizes on the drum A surface. Page Laser Scanner Unit Compensates the vertical angle at which the laser beam hits on of the polygon mirror segments.

Each mirror corresponds to one scanned line width on the drum when the laser beam scans on it. Page 84 below. Page 87 B is approximately 0. The non-exposed areas of the drum A repel the positively charged toner as these areas maintain the positive charge. Page Transfer On the other hand, the bias current is reduced to Page Fusing The temperature of the heat roller A is constantly monitored by the engine board using the thermistor and triac. Should the temperature of the heat roller A exceed the predetermined value, the thermal cutout is activated to effectively disconnect the heater lamp C from power.

Page Cleaning [board] E See figure above. This lowers the electrical conductivity of the drum A surface making the residual charge on the drum A surface escape to the ground. Page Paper Feeding System! Page Electrical Control System! CPU uses this signal to determine that the thermistor is faulty and displays Call service personE4.

Page Chapter 5 Contents General instructions Page General Instructions Never attempt to operate the printer with components removed.

Provide an antistatic discharging device, such as a wrist strap, that can effectively discharge your body before touching those components. Page Disassembly 1. Open the top cover. Remove the toner container.

Disconnect the developer connector 1. Remove the developer 2 from the printer while sliding the developer lock lever 3 frontwards. Page Do not place the developer in a dusty area.

If you ship the developer, pack it in the shipping container specifically supplied with the printer. See section Shipping the developer on page Also do not touch the developing roller 5. Do not place floppy disks near the developer. Draw the paper feed unit 1 while pressing the buttons in the direction of arrow A. Pull the main charger unit 1 upwards while pushing main charger release lever 2.

Then, pull the main charger unit 1 frontwards. Open the top cover 1 and MP tray 2. Unlatch two hooks 3. Pull the operator panel 4 towards the front.

Open the top cover 1. Remove two screws 2. Remove the operator panel. Unlatch the four snaps 1 and three hooks 2 on the chassis.

Remove the right cover 3. Remove the left cover 3. Page Removing The Drum Unit 1. Remove the paper cassette and the paper feed unit. Remove the developer unit. Remove the waste toner bottle. Remove the drum unit 1 while pressing the drum lock 2. Detach the release holder 2 by sliding it while pressing the projections A. Remove the feed roller assembly 3 while pressing it in the direction of arrow B. Page Figure Remove the pickup roller and feed roller Pickup gear Z32S 8 is installed of the inside the one way clutch 9.

Remove the paper feed unit. Remove the developer. Remove three connectors 1. Remove the engine relay board 2 while unlatching the latches 3. Page 5. Pull the MP tray paper feed unit 4 out while unlatching two latches 5 off of points A. Page Removing The Transfer Roller 1 can significantly deteriorate the print quality white spots, etc.

Draw the feed unit from the printer. Remove the paper chute 2. Remove the transfer roller 1. Remove the four connectors 1 from the controller unit 2 left side. If you draw the connector while it is slanted, the receptacle may be damaged.

Page 4. Remove the two connectors 3 from the controller unit 2 right side. Remove three screws 4. Remove frame unit 5 while releasing the projections from the catches on the frame unit 5. Page 7. Remove two screws 6. Remove the main board 7. Remove four screws 8. Remove the controller unit lid 9 from the controller unit 2.

Remove and open the controller unit. See pages Remove two connectors 1 from the engine board 2. Remove five screws 3. Remove the engine board 2. Please enter the link of the image. Please enter the link of the video. By posting, you are declaring that you understand this policy: Your name, rating, website address, town, country, state and comment will be publicly displayed if entered.

It is collected for only two reasons: Administrative purposes, should a need to contact you arise. To inform you of new comments, should you subscribe to receive notifications. A cookie may be set on your computer. This is used to remember your inputs.

It will expire by itself. This policy is subject to change at any time and without notice. By submitting a comment, you are declaring that you agree with these rules: Although the administrator will attempt to moderate comments, it is impossible for every comment to have been moderated at any given time.

You acknowledge that all comments express the views and opinions of the original author and not those of the administrator. You agree not to post any material which is knowingly false, obscene, hateful, threatening, harassing or invasive of a person's privacy.

The administrator has the right to edit, move or remove any comment for any reason and without notice. There can be various reasons for poor print quality. Check if the cartridges or toners are full. If so, inkjet printers often require cleaning the printer, the cartridges have dried out, or the print head is broken. With laser printers, calibrating the laser printer is recommended. What is the difference between a laser printer and an inkjet printer? A laser printer prints with a toner and an inkjet printer prints with ink.

How come my inkjet printer has black stripes? In most cases, the inkjet printer cartridge is broken and the cartridge needs to be replaced. What does DPI stand for? DPI stands for Dots Per Inch and is the number of ink droplets per inch that end up on the paper when printing.

Is the manual of the Kyocera FS available in English?